Author Topic: CP4500 setup issue

April 22, 2023, 08:04:11 PM
Read 1501 times

Xavier

  • Newbie
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
Hi everybody,

I have some issue during the setup procedure. 
When I check the voltage at the step 1.4, i only can go from +0.7 to +2.8VDC when i turn the threshold knob (steps 1.1 to 1.3 are OK)
May be this is the reason why I can't trim the channel 1 level and i have 6dB more at the output when the compressor is IN condition

If you have any idea to fix this problem, your help would be very appreciated ;D

Thanks !

April 24, 2023, 04:18:54 PM
Reply #1

JPK

  • Administrator
  • Hero Member
  • *****
  • Posts: 1105
  • Karma: +36/-0
    • View Profile
Check that the left pin of R95 goes from 12VDC to +12VDC when you rotate the threshold from +15 to -15.
Check the value and solder joints of R95, to R99 and U21.
JPK

April 24, 2023, 10:25:29 PM
Reply #2

Xavier

  • Newbie
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
Thank you for your answer but unfortunatly it doesn't work
R95 to R99 are the good one and are correctly soldered
U21 is the good one too and with the right orientation. I tried to replace U21 by U18 but it didn't change anything
I have the correct voltage at the left pin of R95 between -11.77 and + 12.00VDC


April 25, 2023, 03:18:02 PM
Reply #3

JPK

  • Administrator
  • Hero Member
  • *****
  • Posts: 1105
  • Karma: +36/-0
    • View Profile
Can you report the DC voltages on the 8 pins of U21 for the 2 extreme positions of the Threshold?

JPK

April 25, 2023, 09:30:28 PM
Reply #4

Xavier

  • Newbie
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
When the threshold is +15 
pin 1 = 0
pin 2 = 0
pin 3 = 0
pin 4 = -15.82
pin 5 = 0
pin 6 = 0
pin 7 = + 2.84
pin 8 = +16.01

When the threshold is -15
pin 1 = -2.52
pin 2 = -2.52
pin 3 = -2.52
pin 4 = -15.82
pin 5 = 0
pin 6 = 0
pin 7 = +0.72
pin 8 = +16.01

April 26, 2023, 03:16:52 PM
Reply #5

JPK

  • Administrator
  • Hero Member
  • *****
  • Posts: 1105
  • Karma: +36/-0
    • View Profile
The issue is pin 1-2-3 = -2.52V when the threshold is at -15. It should remain at 0 when there is no input signal.
Is it the same if you remove U9?
JPK

April 26, 2023, 07:17:17 PM
Reply #6

Xavier

  • Newbie
  • *
  • Posts: 4
  • Karma: +0/-0
    • View Profile
Sorry i made a mistake (it was too late maybe ::)) the measure was done with the signal IN and the compressor bypassed
So during the step 1.4, with the correct initial conditions, TP13 goes from -1.8 to +2.8 VDC

With no signal U21 pin 1, 2 and 3 are 0 indeed

Then i tested the others conditions and :

step 1.5
TP4 goes from 0.053 --> 0.185 VAC
TP5 goes from 0.36 --> -1.17 VDC
TP11 goes from 0 --> -3.46 VDC
TP12 goes from 0 --> +3.47 VDC

step 1.6
TP1 is +1.48 VAC
TP2 is +1.62 VAC
TP3 is + 1.5 VAC
TP4 is + 0.054 VAC
pin 1 U6 is 0 VDC

step 1.7
TP1 is 1.48 VAC
TP2 is 0.45 VAC
TP3 is 1.49 VAC
TP4 is +0.18 VAC
TP11 is -3.47 VDC
TP12 is +1.14 VDC
TP13 is +1.66 VDC

Even the values seem not so bad, i still have 6dB more when the compressor is IN
« Last Edit: April 26, 2023, 10:13:48 PM by Xavier »

May 03, 2023, 08:07:24 AM
Reply #7

JPK

  • Administrator
  • Hero Member
  • *****
  • Posts: 1105
  • Karma: +36/-0
    • View Profile
Your values are good.
Try swapping U7 with the one from the other channel, in case it is damaged.
JPK